Embedded Solutions CompactPCI F301-3U Instrukcja Użytkownika Pobierz pdf (Strona 26)

The D6 single-board computer is designed

for embedded systems with high computing

performance and multiple high-speed

com mu nication requirements. Unlike typical

PC boards it is screened for -40 to +85°C

operation temperature, components are all

soldered and it is prepared for conformal

coating.

The standard I/O available at the front

panel of the D6 includes two XMC or PMC

modules, two Gigabit Ethernet and one

USB 2.0. If only one XMC module is used,

one VGA and one COM are available at the

front panel. Graphics is provided in the FPGA

which can also be used to implement further

application-speciﬁ c I/O functions. An additio-

nal 32 MB SDRAM is connected to the FPGA,

e.g. for use as graphics memory.

A wide range of different memory is available

on the D6, such as DDR2 SDRAM with ECC

as main memory. The non-volatile memory

comprises up to 8 MB buffered SRAM, 16 KB

FRAM and 1 GB NAND Flash as mass storage

for program memory. A hard-disk slot is also

implemented within 4 HP height. Aside from

parallel ATA support, two serial ATA lines are

available in addition.

A board management controller is imple-

mented to supervise the CPU, all voltages,

processor and board temperature, and reset.

The controller is completely independent of

the CPU and monitors all states of the CPU.

Pentium

M 6U CompactPCI

Server Blade D6

Pentium

M up to 2 GHz

ULV Celeron

M 1 GHz

PCI Express

4 lanes x4, plus 2 x4 (or 1 x8)

4 HP cPCI system slot, 64-bit/66-MHz

Hot-swap, PICMG 2.16 support

Up to 1(2) GB DDR2 ECC SDRAM

Non-volatile SRAM, FRAM

Up to 1GB Flash-on-disk (NAND), hard disk

2 SATA, 2 PATA interfaces

Graphics up to 1280 x 1024

4 Gigabit Ethernet (PCIe)

3 USB 2.0, 2 COM

Individual I/O in FPGA

2 XMC/PMC slots (PCIe)

Together with two P601 Ethernet XMC mo-

dules the D6 can control a total of 12 Gigabit

Ethernet channels at full speed thanks to the

implementation based on PCI Express

Gigabit Ethernet XMC

Module P601

The P601 is a Gigabit Ethernet XMC mezza nine

card suitable for any XMC compliant single-

board computer, such as D6. In contrast to

PMC, the XMC standard deﬁ nes a different

board-to-board connector for support of PCI

Express

The four Ethernet channels on the P601 are

provided by two Ethernet controllers with

two lines each and supported by two x4 PCIe

lanes. With a speciﬁ c set-up the two lines

inside each Ethernet controller can be used as

a redundant channel pair. In this mode one

line is monitored by the other line and the

controller recognizes when an error occurs.

Four 10/100/1000Base-T channels

Alternatively two redundant channel pairs

4 RJ45 connectors at front

2 x4 PCIe lanes

Full and half duplex

1.5 kV electrical

isolation

Custom 6U VMEbus

Reﬂ ective Memory Board

for ETCS Level 2 System

This board provides two high-speed LVDS

channel links for universal I/O on the VME-

bus. It can be used as a reﬂ ective memory in

a VMEbus system. The VMEbus master/slave

interface is built up in FPGA.

Two LVDS channels are supported on the

front via HD-Sub connectors, each channel

with a transmitter and a receiver. Two LVDS

21-bit channel link controllers convert the

I/O signals of the FPGA into three LVDS data

streams and vice versa. The dual-ported

SDRAM is used to exchange data between

VMEbus and LVDS channels and a mezzanine

CPU module.

Trafﬁ c Management Systems

.....................floating softly over the clouds............... not in the mood for waking up..............................

.................... sanft über den Wolken schweben.......... keine Lust, aufzuwachen..........................................

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 37 38

Komentarze do niniejszej Instrukcji

Brak uwag

Embedded Solutions CompactPCI F301-3U Instrukcja Użytkownika Strona 26

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Networking Embedded Solutions CompactPCI F301-3U